Rocky shore morphology

From Coastal Wiki
Revision as of 11:36, 15 June 2016 by Dronkers J (talk | contribs)
Jump to: navigation, search

Morphology [1]

Rocky shores constitute about ¾ of the world coastline. They exist in very different forms. This diversity depends, among other things, on cliff mineralogy, lithology, tectonic history, climate, waves and tides. Some rocky coasts consist of steep plunging cliffs; this is observed when subaerial erosion is minor compared to marine erosion or in cases of volcanic activity or tectonic subsidence. Cliffs which are degraded by subaerial weathering processes are more gently sloping. Such more rounded (often vegetated) cliffs, are called “bluffs”. A common coastal cliff morphology is the slope-over-wall profile: a rounded weathered top and a vertical wall below.

In many cases cliffs are fronted by shore platforms, which can be tens to many hundreds (or even thousands) of meters wide. These shore platforms result from cliff retreat; the outer edge marks the cliff position in the past – often millennia ago, in the case of erosion-resistant rock.

Wave attenuation on the shore platform reduces cliff recession rates[2]. Cliff and shore platform both retreat by erosional processes; the rate of cliff retreat strongly depends on the width of the shore platform. An equilibrium profile is reached when platform retreat and cliff retreat occur at the same pace.

Cliff erosion

Cliff retreat depends on many factors: rock structure (massive, bedding, faulted, granular), rock lithology (permeability, solubility, hardness, jointing), hydraulic action (exposure to waves more or less loaded with debris, tides, currents) and subaerial weathering (by surface and subsurface runoff, freeze-thaw, chemical processes, biota). Hard rock cliffs retreat typically less than 1 cm/year, whereas soft cliffs (consisting of boulder clay, for example) retreat typically more than 1 m/year.

Cliff retreat is often episodic, through rock-fall and toppling, after undercutting of the cliff base by wave quarrying, abrasion and weathering. Wave quarrying is the process of rock dissection by breaking waves, which produce shock pressures and air compression in joints and fissures. Wave abrasion is the process of rock scraping and shattering by abrasive material (rock fragments) moved forth and back by wave-orbital motion. Rock weathering is due to the mechanical action of alternate drying and wetting and salt crystallization in fissures, but also due to chemical processes (dilution) and biotic activity.

Soft-rock cliffs may collapse by slumping or sliding events, which are often preceded by soil creep and triggered by rainwater infiltration. Debris fans at the cliff base after a slumping event are subsequently reworked by wave action; they are washed away or become part of the shore platform. Marine dissolution processes are an important cause of degradation of limestone cliffs, when acidic seawater (containing dissolved CO2) and salt spray enter cracks, joints and fissures. Bio-erosion (by algae and by boring and grazing organisms) also contributes to erosion of calcareous rock[3]. The resulting forms are termed “karst”, featuring caves, arches and stacks.

Figure: Typical rocky shore profiles. Left: Limestone cliff with low-tide terrace. Right: Hard rock cliff with sloping shore platform. Horizontal shore platforms are more characteristic for microtidal cliff coasts and sloping platforms for macrotidal cliff coasts.


Shore platforms [4]

Shore platforms can be either approximately horizontal, with a steep seaward edge, or gently seaward sloping. Tides modulate the frequency and intensity of wave attack at different levels of the shore platform. Sloping platforms prevail under macrotidal conditions and strong wave attack, whereas horizontal platforms are more common on micro-tidal coasts. High-tide terraces are typical for hard-rock coasts and low waves, low-tide terraces for limestone rocks. In the latter case, erosion resistance of the platform surface can be enhanced by carbonate precipitation and other cementing agents (silica, iron). Soft cliffs often have a beach at the base, with an intertidal veneer of sand and gravel.

Several processes contribute to erosion of shore platforms. The rate of platform down-wearing ranges from less than 1 mm/year to a few cm/year. Attack by waves armoured with rock fragments is an effective erosion mechanism, which polishes the platform surface. Fine abrasive material is washed away by waves and currents. However, platform surfaces usually present also many irregularities, with gullies, ponds and potholes scoured in faults, joints and in excavations of less resistant rock around hard outcrops. Chemical and physical weathering plays an important role, through the effects of alternate wetting and drying, salt crystallization and frost. Marine organisms (see Rocky shore habitat) accelerate platform erosion by grazing activity (surface scraping) and by boring of holes (by bivalves). Algae (e.g. kelp) can provide protection against erosion, but plant roots can also widen crevices and dislodge rock fragments.

Related articles

Cliff stabilisation

References

  1. Trenhaile, A.S. 2011. Cliffs and Rock Coasts. In: Treatise on Estuarine and Coastal Science Vol. 3, eds. Flemming, B.W. and Hansom, J.D., Elsevier, p. 171-192
  2. Sunamura, T. 1992. Geomorphology of Rocky Coasts. Wiley, Chichester
  3. Trenhaile, A.S., 1987. The Geomorphology of Rock Coasts. Oxford University Press, 384 pp.
  4. Bird, E.C.F. 2008. Coastal Geomorphology: An Introduction, Second Edition. JohnWiley and Sons, Ltd, pp. 411


The main author of this article is Job Dronkers
Please note that others may also have edited the contents of this article.

Citation: Job Dronkers (2016): Rocky shore morphology. Available from http://www.coastalwiki.org/wiki/Rocky_shore_morphology [accessed on 31-10-2024]