Difference between revisions of "Overtopping resistant dikes"
|Line 32:||Line 32:|
Figure 4 clearly shows that for each mean discharge there are only a small number of waves that give large overtopping volumes. The general behaviour of wave overtopping can be described by a large number of fairly small overtopping waves and a few which are much bigger. These few but bigger waves often cause the damage to the inner slope. In the first years of testing it appeared to be very difficult to measure any hydraulic parameter on the inner slope, like flow velocity or flow depth. The velocities can approach 8 m/s and the water is very turbulent with a lot of air entrainment
Figure 4 clearly shows that for each mean discharge there are only a small number of waves that give large overtopping volumes. The general behaviour of wave overtopping can be described by a large number of fairly small overtopping waves and a few which are much bigger. These few but bigger waves often cause the damage to the inner slope. In the first years of testing it appeared to be very difficult to measure any hydraulic parameter on the inner slope, like flow velocity or flow depth. The velocities can approach 8 m/s and the water is very turbulent with a lot of air entrainment to about . The flow depth .m. the to the and flow flow depth .
Revision as of 13:23, 29 July 2011
In 1953 the Netherlands experienced a major flooding. Studies determined that a lot of the breaches of the dikes were caused by overtopping (and even overflowing) of the dikes. The failure mostly started on the landward part of the structures. All dikes back then were constructed with a relative low crest and a steep landward slope. Since then all major water defences were raised and the landward slopes were made more gentle. The heightening of the dikes was done in such a manner that statistically only once in 10.000 years (in the western part of the Netherlands) 0.1 l/s per m of overtopping would occur. In the 1990ties by law it was decided that all major water defences should be assessed for safety. In these safety assessments it was found that al lot of dikes again should be raised in order to comply with the safety standards. This raised the question if the method to determine the rate of wave overtopping was correct or not. Also the question was put if the safety standard of 0.1 l/s per m once in 10.000 years was adequate. It turned out that that flooding the mechanisms not enough understood and therefore the safety standard was wrongfully determined on basis of testing with overflow instead of overtopping. Additionally, failure mechanisms were not adequate described. This lead to a Dutch national research program on loads on and strength of flood defences. To assess the erosion strength of grass covers on inner slopes and transition zones between slope to horizontal flats, destructive tests using a Wave Overtopping Simulator were performed at several dikes in the Netherlands.
A Wave Overtopping Simulator performs destructive tests on inner slopes of real dikes in order to establish the erosion resistance against overtopping waves from severe storms. The most relevant hydraulic processes to be considered at wave-structure interaction encompass wave reflection, wave dissipation, wave transmission resulting from wave overtopping and wave penetration through the porous structures, wave diffraction, run-up and wave breaking. Focusing on overtopping, additional processes such as trapped air on broken waves and turbulence, induced by local effects at the armour stones and breakwater cover layers, play an important role in order to determine wave induced dynamics. Formulations derived from these experimentations, are, in most of the cases, semiempirical in nature with their form based on physical considerations but empirical constants determined by fitting to experimental data. The role of scaling factors for dissipation mechanisms due to wave breaking, turbulence and generation of eddies in the fluid region as well as turbulence and friction within the porous material, is also not well established in the physical test. Besides the problem of the scaling technique, other features related with the duration of the experiment programs, wave flume dimensions or economical cost have to be considered. Due to poor repeatability, a large number of experiments have to be carried out in order to define confidence intervals. Moreover, experimental investigation on large-scale models is expensive and measurements within breaking waves can be very complex, due to the aerated and transient nature of the water surface. As a consequence, formulations extracted from the experimental tests present several restrictions. They can only be applied to a structure with a geometry similar or almost identical to the one tested and under identical wave characteristics. An analytical approach is not possible because of the complexity of the problem. A great effort has therefore been made over the last decades in the numerical modelling of wave interaction with coastal structures to overcome these limitations. Nonlinear Shallow Water (NSW), Boussinesq-type and Navier-Stokes equations models have traditionally been used. SPH models have also appeared in the last years as an alternative. However, they are in an early stage to be used as predictive tool.
Definition, design and function
Dikes and levees are applied everywhere there is a hinterland which needs protection against flooding. These protection measures prevent an area from flooding thus enabling economic and sociologic activities also at high water levels. The dikes are designed in such a way that they are geotechnical stable under normal and extreme conditions. Dutch dikes are designed permitting no overtopping. Of course no overtopping cannot be guaranteed. The structures which are described here are mainly grass covered inner or landward slopes of these dikes and levees such as the ones found in the Netherlands. They are mostly made with a sand core covered by a clay layer on the slopes and the crest.
The typical geometry of dikes and levees is an outer or seaward slope then a crest and then a landward slope (right-hand side of Figure 1). The function of the landward slopes is stability of the dike structure and for guidance of overtopping waves or water flowing over the crest to the inlands. The landward slopes must be able to resist loads induced by design conditions. The slope angles as well as the width of the crest vary. In the Dutch case, sea dikes have a typical landward slope 1v:3h. River dikes are mostly steeper, up to 1v:2h. The height of the dikes also varies a lot. This depends on the local hydraulic conditions and on the norm frequency of water level for which the dike is designed. This varies from 1/10,000 per year for sea defences in the western part of the Netherlands to 1:1,250 years for dikes along rivers.
Dikes and levees protect up to a certain level. Absolute safety is impossible. The level to which a dike or a levee protects from flooding depends on the hydraulic regime, the physics of the structure (geometric and geotechnical) and the intended risk reduction or allowable risk to which it is designed. This implies that an economic optimum or in most cases the availability of funds defines the achievable level of risk reduction. Almost two third of the the Netherlands lays below sealevel and therefore has to be protected by dikes or other flood protection structures (including dunes). The dikes in the Netherlands are currently designed based on exceedance of a certain water level that is extrapolated from a long time series (over 200 years) and scientific hind casting. From these water levels, corresponding wave action is calculated. The combination of water level and hydraulic conditions determines the design conditions. Back in 1956, the first Delta Committee already did some early calculations and concluded that the level of protection of the western part of the Netherlands should be higher than in other parts (highest economic value). They found that this part should have a protection level (based on exceedance of water level) of once in a hundred thousand years. They knew dikes to have a large residual strength in the designs. They assumed this to be a factor 10 resulting in lowering the norm to once in ten thousand years. In 1996 the safety levels in the Netherlands were registered in the Water Defence Act. In 2009 this Act was replaced by the Water Act. In the Act of 1996 it was stated that the basis for the safety standards should be altered from exceedance of a certain water level to a risk based approach. This is now developing within the Dutch Floris project.
Experience with function and performance
The landward slope of dikes proved a weak spot during the flooding of 1953 in the Netherlands (over 1,800 people drowned). Back then the dikes were much lower than today. This event led to the Delta Plan recommended heightening the dikes and to milden the landward slopes to 1:3 or even milder to reduce erosive impact of overtopping waves. Before 1953 the angels of the landward slopes were very steep 1:2 or even steeper. Another example is the impact of hurricane Katrina on New Orleans where a lot of landward slopes failed before the water level reached the crest of the levees. Water coming over the dikes or levees does not necessarily mean danger. If the area can cope with a certain amount of water without causing any or just minor socio-economic damage it may be allowable. To optimize costs and competition for space, the dimensions needed for flood protection is preferably limited. Allowing some water passing the crest of the dike by overtopping waves means the need to heighten (and widen) the dikes decreases. If the dikes are strong enough and the passing amount of water can be handled, the design level of the structure can be lowered. However the effect of overtopping water passing the crest of dikes is not known.
From 2006 and onward, Wave Overtopping Simulators were developed at 19 sections of dikes at 6 different locations in the Netherlands. Destructive tests have shown the behaviour of various inner slopes of dikes, embankments or levees under simulated of wave overtopping, up to a mean overtopping discharge of 125 l/s per m. The following will give a mid-term review, based on four years of destructive testing. Until 2009 overtopping tests with the overtopping simulator have been performed on real dutch dikes, with hydraulic loads consistent with more or less general extreme sea conditions along the Dutch coast (Hs = 2 m). The tests performed in 2010 were located along a river dike but the hydraulic loads induced were from a sea dike (Hs = 1-3 m). The main reason for the 2010 allocation was the fact that this sand dike had a very high sand content (85 and 95%) compared to clay covered dikes more commonly found along the dutch sea coast. The core of the dikes is usually sand although in some cases the core of the dike is bolder clay. The cover layer on the landward slopes of sand dikes is typically 0.6 m thick. The thickness of the cover on the sea side is mostly 1 m. In the test locations we indeed found clay covers on the landward slope mainly in the range of 0.6 m but also a location where the thickness of the clay cover only was 0.4 m was found. In the Netherlands dikes exist with a bolder clay core but these have not been tested yet.
The process of wave overtopping on a dikes and levees is well known (Overtopping Manual, 2007). In contrast, the erosive impact of wave overtopping is not known well, mainly due to the fact that research on this topic cannot be performed on a small scale, as it is practically impossible to scale clay and grass down properly. Only some tests have been performed in large wave flumes, like the Delta flume in the Netherlands and the GWK in Germany, see Smith (1994) and Oumeraci et al. (2000). Therefore, the Wave Overtopping Simulator has been developed; see Van der Meer et al. (2006, 2007 and 2008) for more details. The Simulator consists of a high-level mobile box to store water (see Fig. 3). The maximum capacity is 5.5 m3 per m width (22 m3 for a 4 m wide Simulator). This box is continuously filled with a predefined discharge and emptied at specific times in such a way that it simulates the overtopping tongue of a wave at the crest and inner slope of a dike. The discharge of water is released in such a way that for each overtopping volume of water the flow velocity and thickness of the water tongue at the crest corresponds with the characteristics that can be expected.
Field tests have been carried out at the end of the winter when grass roots are in their worst condition. The design and calibration of the Wave Overtopping Simulator has been described by Van der Meer (2007) and the test results of the first tested dike have been described by Akkerman et al. (2007a and 2007b). Part of the tests in 2008 have been described by Steendam et al. (2008). A summary report on all the testing in 2007 and 2008 has been described by Van der Meer (2008). Each test condition was given by a mean discharge and lasted for 6 hours. Test conditions increased from 0.1 l/s per m to 1; 5; 10; 30; 50 and 75 l/s per m. A full test on a dike section took about one week and often more than 14,000,000 litres of water flowed over the inner slope of 4 m width. Each test condition consisted of simulation of the required distribution of overtopping volumes (Overtopping Manual, 2007). Such a distribution depends on expected conditions at sea: a larger significant wave height (as at sea dikes) will show fewer overtopping waves, but the volume in the overtopping waves will be bigger than for a smaller wave height (as for example at river dikes). All tests until 2009 have assumed a significant wave height of 2 m with a wave steepness of 0.04 (using the peak period). In 2010 also tests have been performed with a significant wave height of 3 m and 1 m. Distributions of overtopping volumes for this condition and for various mean discharges are given in Figure 4.
Figure 4 clearly shows that for each mean discharge there are only a small number of waves that give large overtopping volumes. The general behaviour of wave overtopping can be described by a large number of fairly small overtopping waves and a few which are much bigger. These few but bigger waves often cause the damage to the inner slope. In the first years of testing it appeared to be very difficult to measure any hydraulic parameter on the inner slope, like flow velocity or flow depth. The velocities can approach 8 m/s and the water is very turbulent with a lot of air entrainment (estimated to be about 10%). The maximum flow depth is about 0.25 m. It is assumed that the front velocity is similar to the maximum depth averaged velocity and that flow velocity and flow depth have the same shape of record in time.
- Overtopping Manual, 2007. EurOtop; Wave Overtopping of Sea Defences and Related Structures – Assessment Manual. UK: N.W.H. Allsop, T. Pullen, T. Bruce. NL: J.W. van der Meer. DE: H. Schüttrumpf, A. Kortenhaus. [www.overtopping-manual.com]
- Smith, G.M., 1994. Grasdijken. Graserosie, reststerkte en golfoverslag. WL|Delft Hydraulics report H1565 (In Dutch)
- Oumeraci, H., Schüttrumpf, H., Möller, J., and Kudella, M., 2000. Large scale model tests on wave overtopping with natural sea states. LWI-Bericht Nr. 852.
- Van der Meer, J.W., Bernardini, P, Akkerman, G.J., and Hoffmans, G.J.C.M., 2007. The wave overtopping simulator in action. ASCE, proc Coastal Structures, Venice, Italy. Van der Meer, J.W., W. Snijders and E. Regeling, 2006. The wave overtopping simulator. ASCE, proc. ICCE 2006, San Diego, 4654-4666.
- Van der Meer, J.W., Steendam, G.J., de Raat, G. and Bernardini, P., 2008. Further developments on the wave overtopping simulator. ASCE, proc. ICCE 2008, Hamburg. Van der Meer, J.W., 2007. Design, construction, calibration and use of the wave overtopping simulator. ComCoast, Workpackage 3: Development of Alternative Overtopping-Resistant Sea Defences, phase 3. [www.comcoast.org].
- Van der Meer, J.W., 2008. Erosion strength of inner slopes of dikes against wave overtopping. Preliminary conclusions after two years of testing with the Wave Overtopping Simulator. Summary Report.
- Akkerman, G.J., Bernardini, P, van der Meer, J.W., Verheij, H., van Hoven, A., 2007a. Field tests on sea defences subject to wave overtopping. ASCE, proc. Coastal Structures CSt07, Venice, Italy.
- Akkerman, G.J, van Gerven, K.A.J., Schaap, H.A., and van der Meer, J.W., 2007b. Wave overtopping erosion tests at Groningen sea dyke. ComCoast, Work package 3: Development of Alternative Overtopping-Resistant Sea Defences, phase 3. [www.comcoast.org].
- Steendam, G.J., de Vries, W., van der Meer, J.W., van Hoven, A., de Raat, G. and Frissel, J.Y. , 2008. Influence of management and maintenance on erosive impact of wave overtopping on grass covered slopes of dikes. Proc. FloodRisk, Oxford, UK.
Please note that others may also have edited the contents of this article.