Wave transformation

From Coastal Wiki
Revision as of 23:28, 17 September 2008 by Tasomerville (talk | contribs)
Jump to: navigation, search

The following types of transformation are mainly related to wave phenomena occurring in the natural environment. When the waves approach the shoreline, they are affected by the seabed through processes such as refraction, shoaling, bottom friction and wave-breaking. However, wave-breaking also occurs in deep water when the waves are too steep. If the waves meet major structures or abrupt changes in the coastline, they will be transformed by diffraction. If waves meet a submerged reef or structure, they will overtop the reef. These phenomena will be further explained in the following. The following types of wave transformation occur mainly in connection with ports and the like. If the waves meet a steep structure, reflection will take place, and if the waves meet a permeable structure, partial transmission will take place. These phenomena will not be discussed further.


Summary of transformation types

The following is a summary of the transformation types to be found in nature.

Depth refraction

Fig 1. Wave refraction (and breaking).

Depth-refraction is the turning of the direction of wave propagation when the wave fronts travel at an angle with the depth contours at shallow water. The refraction is caused by the fact that the waves propagate more slowly in shallow water than in deep water. A consequence of this is that the wave fronts tend to become aligned with the depth contours. Currents can also result in refraction and this is termed current refraction.

Fig. 2. Wave diffraction in a port (from a numerical simulation with a short wave model).

Diffraction

Diffraction can be seen when there are sheltering structures such as breakwaters. Diffraction is the process by which the waves propagate into the lee zone behind the structures by energy transmittance laterally along the wave crests.

Fig. 3. Shoaling

Shoaling

Shoaling is the deformation of the waves, which starts when the water depth becomes less than about half the wavelength. The shoaling causes a reduction in the wave propagation velocity as well as shortening and steeping of the waves.

Bottom friction

Bottom friction causes energy dissipation and thereby wave height reduction as the water depth becomes more and more shallow. Friction is of special importance over large areas with shallow water.

Depth-induced wave-breaking

Depth-induced wave-breaking of individual waves starts when the wave height becomes greater than a certain fraction of the water depth. As a rule of thumb, the wave height of an individual wave at breaking is often said to be around 80% of the water depth, but this is a very approximate figure. Breaking waves are generally divided into three main types, depending on the steepness of the waves and the slope of the shoreface:

  • Spilling takes place when steep waves propagate over flat shorefaces. Spilling breaking is a gradual breaking which takes place as a foam bore on the front topside of the wave over a distance of 6– 7 wavelengths.
  • Plunging is the form of breaking where the upper part of the wave breaks over its own lower part in one big splash whereby most of the energy is lost. This form of breaking takes place in cases of moderately steep waves on moderately sloping shorefaces.
  • Surging is when the lower part of the wave surges up on the foreshore in which case there is hardly any surf-zone. This form of breaking takes place when relatively long waves (swell) meet steep shorefaces.
Fig. 4. Depth-induced wave-breaking: spilling, plunging and surging.
Fig. 5. White capping can be seen on these irregular directional storm waves
Fig. 6. Wave-overtopping of breakwater in a flume test.
Fig. 7. Wave-overtopping of breakwater in nature.

Wave set-up

Wave set-up is a very important phenomenon in the surf-zone hydrodynamics. This is a local elevation in the mean water level on the foreshore, caused by the reduction in wave height through the surf-zone. The wave set-up is proportional to the wave height at breaking. As a rule of thumb, the wave set-up is 20% of the offshore significant wave height. Gradients in wave set-up, e.g. in partly sheltered areas near port entrances, will generate local circulation in the surf-zone towards the sheltered area.

Wave swash

Wave swash or Wave uprush is the propagation of the waves onto the beach slope. The swash consists of an onshore phase with decelerating upwards flow (uprush or swash) and an offshore phase with accelerating downwards flow (downrush or backwash)

Wave run

Wave run-up is the sum of the wave set-up and the wave swash. The wave run-up is this the maximum level the waves reach on the beach relative to the still water level. The run-up height exceeded by 2% of the run-up events is denoted R2%. The relationship: R2% = 0.36g1/2tanß H01/2T has been obtained in studies[1]. Tanß is the beach slope, and H0 and T are the significant wave height and period at deep water. For typical storm waves this gives: R2% ~ 6 tanß H0.

White-capping

White-capping or top-breaking is steepness-induced wave-breaking, which occurs in deeper water when the wave height becomes too large compared to the wavelength. (see Fig. 5.)

Wave overtopping

Wave-overtopping takes place when waves meet a submerged reef or structure, but also when waves meet an emerged reef or structure lower than the approximate wave height. During over-topping, two processes important to the coastal processes take place: wave transmission and the passing of water over the structure. (see Fig. 6.)



References

  1. by Holman (1986) and Nielsen and Hanslow (1991)

Further reading

Mangor, Karsten. 2004. “Shoreline Management Guidelines”. DHI Water and Environment, 294pg.
The main author of this article is Mangor, Karsten
Please note that others may also have edited the contents of this article.

Citation: Mangor, Karsten (2008): Wave transformation. Available from http://www.coastalwiki.org/wiki/Wave_transformation [accessed on 28-03-2024]